Saturday, April 21, 2012

Wood See-Saw Swing

I looked for instructions on how to build a see saw swing out of wood. Couldn't find any. BUT lucky for me my neighbor had a swing so I had a reference for measurements. 

You need:
3  8ft treated 2x2's ( had one 10 ft 2x4, and I ripped it on my table saw)
scraps of ply wood, or planks for the seats
4 5 1/2 inch bolts (I used 6 inch)
1 1/2 inch (ish) screws
3 inch screws

Cut 2x2's:
2 7ft long (swinging bars)
2 1 ft long (foot rests)
2 3 ft long (seat supports)
2 14 in long (swing supports)

Then cut the seats
They are about 10 inches front to back, and 10 inches at the widest point. I used 3/4 in ply wood, just scraps I had.



Drill your holes in the seat supports at the 12 inch mark and the 24 inch mark for the bolts. I used 3/8 in bolts. Place one of the foot rests between the seat supports before screwing the seats down. This will help you get your spacing right so the swinging bars can fit . 4 1 1/2 in screws on each seat.
Back View
Now drill your bolt holes on the swinging bars. 1 1/2 in from the top

And 12 in from the bottom

Now drill the holes in your top supports 1 inch in on each side. They should be 12 inches apart, just like the holes on the seat supports.

Turn the swinging bars on their side so the holes are on the right and left, not the top and bottom, and screw the foot rests on the bottom with 3 inch screws. 2 or 3 screws on each.
Bolt the swinging bars to the seat supports.
Screw the supports to the top of the swing set with 3 in screws. Use a scrap 2x2 to place between them while you screw it down to keep the spacing right,

Then bolt the swing to the top supports and she is ready to go!


I think I might cut some dowel rods, drill another hole on each bar about 1 ft up from the seats and slide the dowels through. One screw in the center should hold them, then the kids would have some handle bars.

Seriously, they LOVE it. (it's bigger then the ones you can buy, so it swings higher)

4 comments:

  1. I love this blog, and I hope you keep it up! I love seeing your projects and how to do them.

    ReplyDelete
  2. Sữa ong chúa linh nhâm là gì?Chị em phụ nữ chúng ta từ lâu đã tin tưởng vào tác dụng làm đẹp từ mật ong.
    Cá trắm đen làm món gì ngon?Thịt cá trắm chắc, thơm ngon và được chế biến thành rất nhiều các món ngon như cá trắm kho, cá trắm nấu canh chua hay sốt cà chua.
    Cách làm cá chép om dưa ngonVào thời tiết se lạnh mà được thưởng thức món cá chép om dưa với hương vị thơm ngon, hấp dẫn của thì không thể chê vào đâu được.
    Cháo trai có tác dụng gì?Thịt trai được chế biến thành nhiều món ăn ngon, lạ miệng hấp dẫn, đặc biệt món cháo trai không chỉ món ăn lạ miệng mà còn món ăn bổ dưỡng, chữa bệnh tuyệt vời
    Rau tía tô có tác dụng trị bệnh gì?Để giúp mọi người hiểu rõ hơn tác dụng của loại rau thơm này, sau đây chúng tôi xin chia sẻ một số thông tin ở bài viết dưới đây. Mời bạn cùng xem nhé!
    Tác dụng của rau tía tô với bà bầuĐặc biệt, đối với bà bầu , rau tía tô có những tác dụng đến bất ngờ mà ít ai biết đến.
    Quả bồ kết có tác dụng gì?Đến khi nước nguội thì lấy tay đẩy trĩ cho thụt vào và băng lại để giữ.
    Điều trị viêm phế quản cấp ở trẻ emViêm phế quản là bệnh thường gặp ở trẻ em, bất kể thời tiết thế nào. Và nếu không được chữa trị kịp thời và đúng cách, căn bệnh này rất dễ trở thành mạn tính.
    Điều trị viêm phế quản mãn tính ở trẻ sơ sinhTrẻ sơ sinh rất dễ bị mắc các bệnh đường hô hấp do sức đề kháng còn non yếu. Một trong số các bệnh dễ gặp khi thời tiết thay đổi đó là viêm phế quản.
    Viêm phế quản co thắt ở người lớn có lây không?Tập thể dục đều đặn không chọn các môn thể thao quá sức, làm việc và nghỉ ngơi hợp lý tránh tình trạng stress kéo dài.
    Cách làm món cá thu sốt cà chuaCá thu là loại thực phẩm có giá trị dinh dưỡng cao, dễ dàng có thể chế biến thành món ăn nhiều hấp dẫn như nướng cá thu, kho riềng, sốt cà chua, kho Tô, kho tiêu, làm chả, làm rước, nấu bún

    ReplyDelete
  3. How well has it held up over time? My 70lb 9 year old has outgrown her old small metal swingset and I have built a larger wooden one (Home Depot Kit), and would like to build a glider like this. Will this one hold 150-200 lbs of children? I'm concerned that the 2x2s will split where the vertical 7ft swinging bars attach to the 14in horizontal swing supports. I'm wondering if I should go with 2x4 instead. The geometry should be the same. I would definitely want to put in the dowels for handles, though.

    ReplyDelete
    Replies
    1. Also, does it swing ok with wood-on-wood where the seat supports and swing supports are bolted to the vertical swinging bars? Or should I put washers in there? Obviously you don't tighten it down snug. Did you use nylon locking washers?

      Delete